1/0 AWG 0 Gauge Positive Battery Cable Custom MadeCopper battery cable conductor and copper connectors! This custom made top post positive battery cable comes with a top quality copper top post positive connector which is tin plated to resist corrosion, double crimped onto the cable and then you choose the length of the cable as well as your choice of an optional ring terminal available in various sizes, on the opposite end. You choose your length, which is measured from hole center of one connector to the hole center of the connector on the other end. The options for length and connectors are located near purchase buttons. The optional lug choices for the opposite end are 5/16 (fits 5/16 bolt & M8) or 3/8 (fits 3/8 bolt & M10) with adhesive heat shrink tubing applied matching the wire color. The heat shrink has a meltable glue lining to help seal your cable from air and moisture. The copper connectors feature a tin electro-plating which is resistant to the types of corrosion you’ll typically see on bare copper terminals. If you need something special with regard to the length or lugs or heat shrink color which are outside the available options please send us a message and we may be able to help you out. ABOUT THE WIRE USED: This 1/0 AWG Gauge extreme battery cable is specially designed to meet the demands of various environments while staying extremely flexible. Full AWG sized copper conductor made from 99.9% pure annealed electrolytic copper, will you get maximum power. The insulation and jacket compounds are specially formulated to stay flexible even in cold weather and carry a -49C to 105C temperature rating. The jacket is resistant to chemicals, water, abrasions, oil, sunlight and has a color coded dual extrusion jacket with a white inner insulation which would show any damage to the outer cable more clearly. This cable is rated up to 600 Volts and is suitable for use in automotive applications, solar battery bank wiring, power inverter battery cables, marine battery cables and many other applications calling for a durable yet flexible battery cable. The battery cables meet the requirements of SAE J1127 and J378 making them ABYC and US Coast Guard approved for boat and marine use. BENEFITS OVER WELDING CABLE: Full AWG Size Copper Conductor TPE Jacket is Oil Resistant where EPDM on many welding cables is a poor insulator against oil SAE Rated for Automotive and Marine Uses BENEFITS OVER CCA POWER WIRE: Our cable is Copper…REAL COPPER but watch out for other “CCA Cable” as CCA Means Copper Clad Aluminum so you’d be using Aluminum which is a poor conductor compared to this pure copper cable! You have to use larger sizes of aluminum CCA cable, approximately 2 sizes larger to get close to the same power delivery as real copper cable! If you care about maximum power use our cable! The jacket on the cable reads as follows: BATTERYCABLESUSA.COM 1/0 AWG MARINE SAE J378/J1127 600V (-49C to 105C) MADE IN USA Benefits: ABYC and USCG Approved for use on boats SAE J1127 Approved SAE J378 Approved TPE Jacket is Very Resistant to Oil, Water, Acid, Gas, Tears and Abrasions The Jacket Insulation Meets UL FT1 Flame Resistance Rating Annealed Electrolytic Copper with Class K (Type III) Rope Lay for flexibility FULL AWG Copper Content Foot marking on jacket every foot ( ><FT ) MADE IN THE USA Specifications: Conductor Size: 1/0 AWG Stranding: 1045 strands of copper (30 AWG ea strand, rope lay Class K) Outside Diameter of stranding: 0.397 inches (nominal) Outside Diameter of finished cable: 0.610 inches (nominal) Amps: Rated to handle 285 amps continuous outside of engine space (242 amps continuous inside engine space) Weight: 0.460 lbs per foot Suitable Uses: Automotive Battery Cables Marine / Boat Battery Cables Solar Battery Bank Array Forklift Charging Cables Power Inverter Cables Welding Cable Leads Amplifier Wiring …and many other uses Final pointers on lug sizing….most threaded stud batteries will have either a 5/16 or 3/8 inch stud. Most of the time the negative will be 5/16 so if the positive is the same size it is also 5/16, but if your battery stud is larger on the positive it will most likely be a 3/8. There are exceptions to the rule so please contact the manufacturer or measure. You can search online for bolt sizing tables which will help.
1/0 AWG 0 Gauge Negative Battery Cable Custom Made Copper battery cable conductor and copper connectors! This custom made top post negative battery cable comes with a top quality copper top post negative connector which is tin plated to resist corrosion, double crimped onto the cable and then you choose the length of the cable as well as your choice of an optional ring terminal available in various sizes, on the opposite end. You choose your length, which is measured from hole center of one connector to the hole center of the connector on the other end. The options for length and connectors are located near purchase buttons. The optional lug choices for the opposite end are 5/16 (fits 5/16 bolt & M8) or 3/8 (fits 3/8 bolt & M10) with adhesive heat shrink tubing applied matching the wire color. The heat shrink has a meltable glue lining to help seal your cable from air and moisture. The copper connectors feature a tin electro-plating which is resistant to the types of corrosion you’ll typically see on bare copper terminals. If you need something special with regard to the length or lugs or heat shrink color which are outside the available options please send us a message and we may be able to help you out. ABOUT THE WIRE USED: This 1/0 AWG Gauge extreme battery cable is specially designed to meet the demands of various environments while staying extremely flexible. Full AWG sized copper conductor made from 99.9% pure annealed electrolytic copper, will you get maximum power. The insulation and jacket compounds are specially formulated to stay flexible even in cold weather and carry a -49C to 105C temperature rating. The jacket is resistant to chemicals, water, abrasions, oil, sunlight and has a color coded dual extrusion jacket with a white inner insulation which would show any damage to the outer cable more clearly. This cable is rated up to 600 Volts and is suitable for use in automotive applications, solar battery bank wiring, power inverter battery cables, marine battery cables and many other applications calling for a durable yet flexible battery cable. The battery cables meet the requirements of SAE J1127 and J378 making them ABYC and US Coast Guard approved for boat and marine use. BENEFITS OVER WELDING CABLE: Full AWG Size Copper Conductor TPE Jacket is Oil Resistant where EPDM on many welding cables is a poor insulator against oil SAE Rated for Automotive and Marine Uses BENEFITS OVER CCA POWER WIRE: Our cable is Copper…REAL COPPER but watch out for other “CCA Cable” as CCA Means Copper Clad Aluminum so you’d be using Aluminum which is a poor conductor compared to this pure copper cable! You have to use larger sizes of aluminum CCA cable, approximately 2 sizes larger to get close to the same power delivery as real copper cable! If you care about maximum power use our cable! The jacket on the cable reads as follows: BATTERYCABLESUSA.COM 1/0 AWG MARINE SAE J378/J1127 600V (-49C to 105C) MADE IN USA Benefits: ABYC and USCG Approved for use on boats SAE J1127 Approved SAE J378 Approved TPE Jacket is Very Resistant to Oil, Water, Acid, Gas, Tears and Abrasions The Jacket Insulation Meets UL FT1 Flame Resistance Rating Annealed Electrolytic Copper with Class K (Type III) Rope Lay for flexibility FULL AWG Copper Content Foot marking on jacket every foot ( ><FT ) MADE IN THE USA Specifications: Conductor Size: 1/0 AWG Stranding: 1045 strands of copper (30 AWG ea strand, rope lay Class K) Outside Diameter of stranding: 0.397 inches (nominal) Outside Diameter of finished cable: 0.610 inches (nominal) Amps: Rated to handle 285 amps continuous outside of engine space (242 amps continuous inside engine space) Weight: 0.460 lbs per foot Suitable Uses: Automotive Battery Cables Marine / Boat Battery Cables Solar Battery Bank Array Forklift Charging Cables Power Inverter Cables Welding Cable Leads Amplifier Wiring …and many other uses Final pointers on lug sizing….most threaded stud batteries will have either a 5/16 or 3/8 inch stud. Most of the time the negative will be 5/16 so if the positive is the same size it is also 5/16, but if your battery stud is larger on the positive it will most likely be a 3/8. There are exceptions to the rule so please contact the manufacturer or measure. You can search online for bolt sizing tables which will help.
2 AWG 2 Gauge Positive Battery Cable Custom MadeCopper battery cable conductor and copper connectors!This custom made top post positive battery cable comes with a top quality copper top post positive connector which is tin plated to resist corrosion, double crimped onto the cable and then you choose the length of the cable as well as your choice of an optional ring terminal available in various sizes, on the opposite end.You choose your length, which is measured from hole center of one connector to the hole center of the connector on the other end. The options for length and connectors are located near purchase buttons. The optional lug choices for the opposite end are 5/16 (fits 5/16 bolt & M8) or 3/8 (fits 3/8 bolt & M10) with adhesive heat shrink tubing applied matching the wire color. The heat shrink has a meltable glue lining to help seal your cable from air and moisture. The copper connectors feature a tin electro-plating which is resistant to the types of corrosion you’ll typically see on bare copper terminals.If you need something special with regard to the length or lugs or heat shrink color which are outside the available options please send us a message and we may be able to help you out. ABOUT THE WIRE USED:This 2 AWG Gauge extreme battery cable is specially designed to meet the demands of various environments while staying extremely flexible. Full AWG sized copper conductor made from 99.9% pure annealed electrolytic copper, will you get maximum power. The insulation and jacket compounds are specially formulated to stay flexible even in cold weather and carry a -49C to 105C temperature rating. The jacket is resistant to chemicals, water, abrasions, oil, sunlight and has a color coded dual extrusion jacket with a white inner insulation which would show any damage to the outer cable more clearly. This cable is rated up to 600 Volts and is suitable for use in automotive applications, solar battery bank wiring, power inverter battery cables, marine battery cables and many other applications calling for a durable yet flexible battery cable. The battery cables meet the requirements of SAE J1127 and J378 making them ABYC and US Coast Guard approved for boat and marine use.BENEFITS OVER WELDING CABLE: Full AWG Size Copper Conductor TPE Jacket is Oil Resistant where EPDM on many welding cables is a poor insulator against oil SAE Rated for Automotive and Marine UsesBENEFITS OVER CCA POWER WIRE: Our cable is Copper…REAL COPPER but watch out for other “CCA Cable” as CCA Means Copper Clad Aluminum so you’d be using Aluminum which is a poor conductor compared to this pure copper cable! You have to use larger sizes of aluminum CCA cable, approximately 2 sizes larger to get close to the same power delivery as real copper cable! If you care about maximum power use our cable!The jacket on the cable reads as follows:BATTERYCABLESUSA.COM 2 AWG MARINE SAE J378/J1127 600V (-49C to 105C) MADE IN USABenefits: ABYC and USCG Approved for use on boats SAE J1127 Approved SAE J378 Approved TPE Jacket is Very Resistant to Oil, Water, Acid, Gas, Tears and Abrasions The Jacket Insulation Meets UL FT1 Flame Resistance Rating Annealed Electrolytic Copper with Class K (Type III) Rope Lay for flexibility FULL AWG Copper Content MADE IN THE USASpecifications: Conductor Size: 2 AWG Stranding: 665 strands of copper (30 AWG ea strand, rope lay Class K) Outside Diameter of stranding: 0.320 inches (nominal) Outside Diameter of finished cable: 0.510 inches (nominal) Amps: Rated to handle 210 amps continuous outside of engine space (178 amps continuous inside engine space) Weight: 0.302 lbs per foot Suitable Uses: Automotive Battery Cables Marine / Boat Battery Cables Solar Battery Bank Array Forklift Charging Cables Power Inverter Cables Welding Cable Leads Amplifier Wiring …and many other uses
2 AWG 2 Gauge Negative Battery Cable Custom MadeCopper battery cable conductor and copper connectors!This custom made top post negative battery cable comes with a top quality copper top post negative connector which is tin plated to resist corrosion, double crimped onto the cable and then you choose the length of the cable as well as your choice of an optional ring terminal available in various sizes, on the opposite end.You choose your length, which is measured from hole center of one connector to the hole center of the connector on the other end. The options for length and connectors are located near purchase buttons. The optional lug choices for the opposite end are 5/16 (fits 5/16 bolt & M8) or 3/8 (fits 3/8 bolt & M10) with adhesive heat shrink tubing applied matching the wire color. The heat shrink has a meltable glue lining to help seal your cable from air and moisture. The copper connectors feature a tin electro-plating which is resistant to the types of corrosion you’ll typically see on bare copper terminals.If you need something special with regard to the length or lugs or heat shrink color which are outside the available options please send us a message and we may be able to help you out. ABOUT THE WIRE USED:This 2 AWG Gauge extreme battery cable is specially designed to meet the demands of various environments while staying extremely flexible. Full AWG sized copper conductor made from 99.9% pure annealed electrolytic copper, will you get maximum power. The insulation and jacket compounds are specially formulated to stay flexible even in cold weather and carry a -49C to 105C temperature rating. The jacket is resistant to chemicals, water, abrasions, oil, sunlight and has a color coded dual extrusion jacket with a white inner insulation which would show any damage to the outer cable more clearly. This cable is rated up to 600 Volts and is suitable for use in automotive applications, solar battery bank wiring, power inverter battery cables, marine battery cables and many other applications calling for a durable yet flexible battery cable. The battery cables meet the requirements of SAE J1127 and J378 making them ABYC and US Coast Guard approved for boat and marine use.BENEFITS OVER WELDING CABLE: Full AWG Size Copper Conductor TPE Jacket is Oil Resistant where EPDM on many welding cables is a poor insulator against oil SAE Rated for Automotive and Marine UsesBENEFITS OVER CCA POWER WIRE: Our cable is Copper…REAL COPPER but watch out for other “CCA Cable” as CCA Means Copper Clad Aluminum so you’d be using Aluminum which is a poor conductor compared to this pure copper cable! You have to use larger sizes of aluminum CCA cable, approximately 2 sizes larger to get close to the same power delivery as real copper cable! If you care about maximum power use our cable!The jacket on the cable reads as follows:BATTERYCABLESUSA.COM 2 AWG MARINE SAE J378/J1127 600V (-49C to 105C) MADE IN USABenefits: ABYC and USCG Approved for use on boats SAE J1127 Approved SAE J378 Approved TPE Jacket is Very Resistant to Oil, Water, Acid, Gas, Tears and Abrasions The Jacket Insulation Meets UL FT1 Flame Resistance Rating Annealed Electrolytic Copper with Class K (Type III) Rope Lay for flexibility FULL AWG Copper Content MADE IN THE USASpecifications: Conductor Size: 2 AWG Stranding: 665 strands of copper (30 AWG ea strand, rope lay Class K) Outside Diameter of stranding: 0.320 inches (nominal) Outside Diameter of finished cable: 0.510 inches (nominal) Amps: Rated to handle 210 amps continuous outside of engine space (178 amps continuous inside engine space) Weight: 0.302 lbs per foot Suitable Uses: Automotive Battery Cables Marine / Boat Battery Cables Solar Battery Bank Array Forklift Charging Cables Power Inverter Cables Welding Cable Leads Amplifier Wiring …and many other uses
6 Gauge AWG custom made battery cable assembly which includes your choice of lugs crimped to the wire with adhesive lined heat shrink to seal the connections. Your choose your wire color, length, and lugs from the options above near the purchase buttons. The copper lug connector (ring terminal) choices are 1/4, 5/16 or 3/8 with adhesive heat shrink tubing applied as follows:Black cable gets Black Heat ShrinkRed cable gets Red Heat ShrinkThe heat shrink has a melt-able glue lining to help seal your cable from air and moisture. The copper lugs feature a tin plating which is resistant to corrosion you’ll see on bare copper ring terminals.If you need something special with regard to the length or lugs outside the available options please send us a message and we may be able to help you out. ABOUT THE WIRE USED:Introducing our multi-rated, multi-purpose, flexible, real copper battery cable. This wire has multiple approvals for use in many electrical installation making it a very unique cable. From the pure electrolytic copper stranding to the durable yet flexible insulation, this cable has been designed to impress. Our UL listed battery cable carries ratings allowing it to be used as marine battery cable listed as UL1426 Boat Cable which maintains a BC-5W2 temperature rating of 105C dry and 75C wet. This wire can be continuously submerged in water with no issues. This fine battery cable exceeds the requirements of ABYC and the USCG (US Coast Guard) for installation on boats.The copper conductor features stranding which is tin plated to resist corrosion. Flexible Type III, Class K stranding is designed to absorb vibration found in motive environments such as automotive and marine thus protecting the cable from premature failure.FEATURES:Meets all applicable boat wiring regulations from ABYC, UL1426,and US Cost Guard for use on boatsRated 600 Volts Max with 105C Dry and 75C Wet (BC-5W2) temperature ratings and will remain flexible in extreme cold weatherJacket and insulation are resistant to oil, gas, fungus, salt water, battery acid, heat, abrasion and sunlightMultiple ratings including – BOAT CABLE (UL1426), THW (building wire), MTW (machine tool wire), AWM (Appliance Wiring Material) and CSA TEWCarries UL VW-1 Flame Resistant RatingIs ROHS CompliantMADE IN THE USA!!!Battery Cable Specifications:Wire Size Nominal Stranding Weight Amp Rating (AWG) O.D.(Inch) Count LBS/FT Continuous* 8 0.249 168 0 .070 80 6 0.324 266 0.114 120 4 0.386 420 0.164 160 2 0.437 665 0.251 210 1 0.518 836 0.333 245 1/0 0.563 1064 0.403 285 2/0 0.615 1330 0.500 330 3/0 0.670 1672 0.614 385 4/0 0.740 2109 0.765 445*Per ABYC/USCG (Inside of engine space de-rate amps shown by 15% due to extra heat)Final pointers on lug sizing….many standard threaded stud batteries will have either a 5/16 or 3/8 inch stud. Most of the time the negative will be 5/16 so if the positive is the same size it is also 5/16, but if your battery stud is larger on the positive it will most likely be a 3/8. There are exceptions to the rule so please contact the manufacturer or measure. You can search online for bolt sizing tables which will help. Smaller batteries like golf cart and PWC batteries often use a 1/4 bolt. Please double check your needs BEFORE ordering
Untitled DocumentStoreFeedbackFollow#14 AWG Gauge 600V THHN Solid Copper Wire Multi Colors Available – UL 500FT Brand new UL 83 Listed Copper Solid 14 Gauge Wire on a 500FT spool. Select your desired color in the options above. All wire is a brand new spool and meets UL 83 standards. ApplicationsFor general use in residential, commercial and industrial installations:- Residential Homes- Commercial Applications – Public buildings.- Hotels.- Warehouses.- Chemical plants.- Petrochemical plants.- They can also be used in ducts or trays.Characteristics• Resistant to:– Heat.- Humidity.– Solvents.– Oils (PR-1).– Gasoline (GR-1).– Fats.- Chemical agents.• Resistant to abrasion and mechanical stress.• Flame retardant.• Smaller outside diameter (20% compared to THHW).• Low coefficient of friction.Contact & Support You can always contact us directly here, we do our best to support our customers and answer any questions. Feel free to send us a message any time. ShippingMost orders are shipped within 12-48 Business Hours. This process is expedited by paying for your item immediately. We supply tracking information directly to your eBay account as soon as it’s available. Payments PayPal is our preferred method of payment. Your PayPal account must be a Verified account. We collect Sales Tax in Illinois as required. © Paladin Distribution Inc.
Untitled DocumentStoreFeedbackFollow#12 AWG Gauge 600V THHN Solid Copper Wire Multi Colors Available – UL Listed Brand new UL 83 Listed Solid Copper 12 Gauge Wire. Select your desired color and length in the options above, if purchasing multiple quantities we can send continuous length. All wire is cut from a brand new roll and meets UL 83 standards.ApplicationsFor general use in residential, commercial and industrial installations:- Residential Homes- Commercial Applications – Public buildings.- Hotels.- Warehouses.- Chemical plants.- Petrochemical plants.- They can also be used in ducts or trays.Characteristics• Resistant to:– Heat.- Humidity.– Solvents.– Oils (PR-1).– Gasoline (GR-1).– Fats.- Chemical agents.• Resistant to abrasion and mechanical stress.• Flame retardant.• Smaller outside diameter (20% compared to THHW).• Low coefficient of friction.Contact & Support You can always contact us directly here, we do our best to support our customers and answer any questions. Feel free to send us a message any time. ShippingMost orders are shipped within 12-48 Business Hours. This process is expedited by paying for your item immediately. We supply tracking information directly to your eBay account as soon as it’s available. Payments PayPal is our preferred method of payment. Your PayPal account must be a Verified account. We collect Sales Tax in Illinois as required. © Paladin Distribution Inc.
Color Temperature 6000K. LED Quantity each LED has 64 SMD. LED Type 3528 SMD chip. Multi-Function Applications : Ideal for backup lights, brake lights, tail lights, parking lights, marker lights, DRLs, and turn signals (resistors may be required for hyperflash prevention).
